*Newly acquired box-fresh Apple II Plus! || Project log + newbie questions*

18 posts / 0 new
Last post
Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
*Newly acquired box-fresh Apple II Plus! || Project log + newbie questions*

 

Hi everyone! I came across this forum when searching regarding the keyboard on my Apple II, and I found this helpful thread about converting to Cherry MX keyswitches. https://www.applefritter.com/content/cherry-mx-datanetics-dc-51-keyboard-switch-adapter

 

So I figured I might as well sign up and say hi. :)

 

I recently acquired this early Apple II Europlus (European Plus variant) which had been sat in its original box for over 30  years! 

It has quite a few goodies with it. The keyboard is a Datanetics Rev. B with green DC-51-01 keyswitches, which is what leads me to believe it is a very early example of a Plus.

 

It has a Videx Videoterm (possibly a clone), a Z-80 SoftCard, 64K, its original disk drive and paddles, the shift mod, and a few other bits and pieces.

 

I have so far had to replace the RIFA, a chip on the disk controller card, and some of the keyswitches took some persuading to come back to life.  I then managed to source a period correct green phosphor CRT to go with it. 

 

It has a few small niggles which I think could likely be resolved with some contact cleaner, like the fact that it sometimes won't boot unless I prod a bunch of socketed chips, or remove and re-insert some cards.

 

Album of images here for anyone interested! :) 

 

Akagi's Apple II

 

I am currently undecided on its fate, but I think I would like to tinker with it and experience a period of computing history that I missed, before I consider moving it on. 

 

Prior to this the oldest computer I had experience with ran Windows 95, so this is all very new to me, and I have already asked lots of stupid questions... 

 

 

So yeah, hi, I'm Akagi. Sometimes known as Panda. Its nice to meet you!

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
My first stupid question is

My first stupid question is:How do I safely remove the space-bar? Does it simply lift off like the rest of the keys, or are there stabilisers that will interfere?

CVT
CVT's picture
Offline
Last seen: 4 hours 17 min ago
Joined: Aug 9 2022 - 00:48
Posts: 1164
Do not remove the spacebar

Do not remove the spacebar with the top cover on! Remove the cover, then you will be able to see the stabilizer rod and unhook it.

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
CVT wrote:Do not remove the
CVT wrote:

Do not remove the spacebar with the top cover on! Remove the cover, then you will be able to see the stabilizer rod and unhook it.

Having just removed the space bar with the top cover on, and then struggled to put it back on again, I wish I'd been patient and read this reply first. xD

Nevertheless I achieved what I needed to, and I know now for future, thanks! 

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
My next stupid question is,

My next stupid question is, if I have a z80 softcard in slot 4, do I start using it by typing pr#4? If so, what should then be displayed? :)

Offline
Last seen: 12 hours 15 min ago
Joined: Jun 29 2018 - 16:55
Posts: 590
Akagi wrote:My next stupid
Akagi wrote:

My next stupid question is, if I have a z80 softcard in slot 4, do I start using it by typing pr#4? If so, what should then be displayed? :)

Depending on the card (pcpi or msft), you need to get the floppy disk image(s) for CP/M and boot from them. I've done this using a FloppyEMU before but there are other ways of course. The Asimov archive has the software disk images available. 

Offline
Last seen: 1 week 1 day ago
Joined: Apr 26 2016 - 08:36
Posts: 738
skate323k137 wrote:Akagi
skate323k137 wrote:
Akagi wrote:

My next stupid question is, if I have a z80 softcard in slot 4, do I start using it by typing pr#4? If so, what should then be displayed? :)

Depending on the card (pcpi or msft), you need to get the floppy disk image(s) for CP/M and boot from them. I've done this using a FloppyEMU before but there are other ways of course. The Asimov archive has the software disk images available. 

 

...which means you should get yourself a disk image handler like a Floppy Emu: https://www.bigmessowires.com/floppy-emu/

Or a Super Serial Card, serial cable, USB-to-serial adapter and ADTPro: https://adtpro.com

 

 

Offline
Last seen: 1 week 1 day ago
Joined: Apr 26 2016 - 08:36
Posts: 738
Night Mission Pinball.

Night Mission Pinball.

 

Respect, man.

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
Thanks both for the tips and

Thanks both for the tips and info. :) 

A more pressing issue though is that my Videx clone doesn't work. 

The machine boots with it installed, but when doing PR#3, there is no display output from the card, and ctrl + bell doesn't result in a beep. 

I have removed all of the chips, cleaned the sockets, re-inserted them, and cleaned the contact on the card and the slot, as well as checking continuity on the cable. 

So I am at a loss now. Is there a chip that is a common failure or anything like that? 

 

I do also have intermittent issues with my Disk II card, so is there a chip on the motherboard which relates to slotted expansion cards? Thanks :) 

 

Might be something better suited to its own thread perhaps. 

Offline
Last seen: 1 month 1 week ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
What piggy tail do you have

What piggy tail do you have connected to the 4 pin connector on the upper front (keyboard facing) end of the card?  The 80 column output should come off two pins of that connector and either go to a "soft switch" that plugs into the mobo or to an RCA jack attached to the monitor or a manual switch.

 

 

 

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
It is a home-made cable that
softwarejanitor wrote:

What piggy tail do you have connected to the 4 pin connector on the upper front (keyboard facing) end of the card?  The 80 column output should come off two pins of that connector and either go to a "soft switch" that plugs into the mobo or to an RCA jack attached to the monitor or a manual switch.

 

 

It is a home-made cable that was already installed on the card when I got the machine.  

 

The top-most pin is connected to the outside of the RCA connector, and the second pin down is connected to the inner post.

 

The bottom two pins are left empty. 

 

I have an RCA switcher box thingy. 

 

 

Offline
Last seen: 1 month 1 week ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
That cable sounds correct, so

That cable sounds correct, so as long as it has continuity that's probably not the problem.

Offline
Last seen: 1 month 1 week ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
Have you tried removing and

Have you tried removing and re-inserting the chips?  In particular the 74161 on the top back (away from keyboard) of the card looks like it may not be seated very well.

 

Edit -- re-reading the thread I see you have.

 

I might check the contents of the firmware in the system monitor.

 

I'd also probably start swapping various chips because I've got spares of just about everything on there, even a couple spare Videx type cards I could swap the Hitachi video chip out with.  But if you don't have that, it's not an option.  The 74LSxxx and 74xxx chips are mostly cheap and easy enough to find that it doesn't hurt to stock spares.

 

 

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
Thanks, yeah I was worried my

Thanks, yeah I was worried my options from here would be either, get an oscilloscope, or start randomly swapping chips.I guess I'll go with the cheaper option haha. 

Offline
Last seen: 1 week 1 day ago
Joined: Apr 26 2016 - 08:36
Posts: 738
The Videx clone card should

The Videx clone card should be fixable.

But if you want to sell it I would buy it right now because it matches the Unitron motherboard of my Clone II+.

Offline
Last seen: 1 week 1 day ago
Joined: Apr 26 2016 - 08:36
Posts: 738
By the way...If you type PR#3

By the way...

If you type PR#3 (with the card inserted in slot 3) and switch the video it SHOULD display the 80 column screen.

If you then type an illegal statement and press return it should beep but the beep is at a much lower frequency than the regular Apple "beep".

 

If it does that, the card is working and not displaying video.  There's an issue with the large CRTC chip or its supporting circuitry. 

If it crashes the machine or the machine becomes non-responsive it is possible that the ROMs on that card are faulty.

 

Pressing RESET after entering 80 column mode via a PR#3 command shoud return you to 40 column mode and restore the familiar "beep".

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
What chips would you start

When I enter PR#3 the blinking cursor on the 40 column display disappears (as expected), however when I then switch monitor inputs to the 80 column card, there is nothing displayed. Ctrl + bell results in silence, any pressing of keys followed by return results in silence, however I can press reset to be returned to the 40 column output. When I switch to 80 column I can also hear a change in the pitch of the electronic hum.

 

What chips would you start with? I can get... 

 

The CD4013BE, 74LS02, 74LS139 (does it matter if this is an N or AN?), 74LS00, 74LS157, 74LS132, 74LS86 (does it matter if this is an N or AN?), 74LS166, UPD4016C-2, and the main controller chip, the HD46505 SP-1. 

 

All of that comes to about £23 but I won't buy all of it if there are some more likely candidates I can begin with. :)  

I can record the behaviour tomorrow if you think it would be helpful! 

Akagi's picture
Offline
Last seen: 3 months 1 week ago
Joined: May 9 2023 - 03:03
Posts: 66
Akagi wrote:When I enter PR#3
Akagi wrote:

When I enter PR#3 the blinking cursor on the 40 column display disappears (as expected), however when I then switch monitor inputs to the 80 column card, there is nothing displayed. Ctrl + bell results in silence, any pressing of keys followed by return results in silence, however I can press reset to be returned to the 40 column output. When I switch to 80 column I can also hear a change in th

I have made a seperate thread for this issue, in the hopes some more people might see it. It is here. Thanks!

Log in or register to post comments